alexix33

Please,
may u help me?
I did a little of confusion using mgcam. I am not sure about the config. Before I had Dreambox 7025. I was part of a server (client), and i used cccam to share. My cline was C: xx.xxx.xx.xx 12000 user1 user1.
There are no proble to see the package that the server transmitted to me, neither my mct local card.
Now i am not able to see anything. You must think that i installed mgcam 1.62 and newcs, but no results
Here newcamd.list, as i setted :
CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 12000
CWS = 127.0.0.1 10110 user1 user1 01 02 03 04 05 06 07 08 09 10 11 12 13 14
CWS = XX.XXX.XX.X 12000 user1 user1 01 02 03 04 05 06 07 08 09 10 11 12 13 14
wan newcs

Below newcs.xml:

<?xml version="1.0"?>
<!--
For setup-issues, look in readme.txt!
If there are other troubles, try different forums or irc channels around ...
-->

<newCSconfig>

<readers name="Card Readers">
<device>
<name>lower</name>
<type>Sci</type>
<node>/dev/sci0</node>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>10110</newcamd_port>
<priority>round</priority>
<sid>
<allow>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</allow>
<deny>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</deny>
</sid>
</device>
<device>
<name>upper</name>
<type>Sci</type>
<node>/dev/sci1</node>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>12000</newcamd_port>
<priority>round</priority>
<sid>
<allow>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</allow>
<deny>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</deny>
</sid>
</device>
</readers>

<radegastserver>
<!-- valid value for enable are:
0,1 - Enable or Disable radegast server. -->
<enabled>no</enabled>

<!-- valid value for port are:
0,65535 - Which port to listen for incomming connections. -->
<port>10001</port>

<!-- valid value for allow are:
ALL - Not active yet. -->
<allow>
<hostname>127.0.0.1</hostname>
</allow>
</radegastserver>
<cache>
<emm>10</emm>
<ecm>10</ecm>
</cache>
<debug>
<level>verbose</level>
<type>init</type>
<output>all</output>
<logfile></logfile>
<console_options></console_options>
<file_options></file_options>
<udp_host>192.168.1.10</udp_host>
<udp_port>1000</udp_port>
<udp_options></udp_options>
<tcp_port>3001</tcp_port>
<tcp_options></tcp_options>
</debug>
<newcamdserver>
<enabled>yes</enabled>
<name>bla</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<userfile>/tmp/users.txt</userfile>
<user>
<name>user1</name>
<password>user1</password>
<au>on</au>
<allow>lower</allow> <!--Use this just when you want give free just some readers to your Users -->
<allow>upper</allow> <!--Use this just when you want give free just some readers to your Users -->
</user>
<user>
<name>user1</name>
<password>user1</password>
<au>on</au>
</user>


</newcamdserver>

</newCSconfig>
What is wrong ?
Why am i not able to connect with ipbox and Auto DHCP ? Is it depending from my router ? I have fastweb connection, one Hag and then Tp-link router TL-WR841N.
In any case i had loaded a manual config. and it is works, because i update new Sif firmware from web.
My ipbox ip address is 192.168.1.xxx.
Is it a problem of some ports i have not open to do sharing ? What port ?

Is it better mbox